Magdalla Port · INMDA

Rope Access Hold Cleaning at Magdalla Port

The upper hold reached without staging

Get a quote

Tell us the vessel, the port and the window. Scoped reply, usually the same working day.

Cleanship Marine provides IRATA rope access teams at Magdalla Port, Gujarat, to clean, inspect and treat the upper areas of cargo holds — hatch coamings, upper frames, transverse bulkheads and the underside of hatch covers — without staging or cherry pickers.

The top third of a cargo hold is where staging costs, schedule and risk all concentrate, and it is the part a deck-level gang cannot reach properly. Rope access removes the scaffolding from the equation entirely. At Magdalla it also fits the schedule: the upper hold can be worked from ropes while the lower hold is still discharging, so the two do not queue behind each other.

What it gets you

Upper hold areas actually reached and cleaned, not just the parts a gang can stand on
No staging cost, no cherry picker and no lost days erecting and striking it
Structural condition at height inspected while the technicians are already there
Fewer people working at height, under a written plan with a rescue capability

Working conditions at Magdalla

Work here runs both alongside and at anchorage depending on the call, and on the passage out where neither gives enough time. The south-west monsoon sets the outer limits of the calendar, roughly June to September, and it affects the anchorage far more than the berth. Access approval runs through Gujarat Maritime Board and the terminal, and the disposal route for residues and washings is fixed before the gang boards rather than found afterwards.

Where we work: River jetties · Outer anchorage
Vessels we see here: Handysize bulk carriers · General cargo ships · Coastal tankers

What we do at Magdalla

IRATA-certified technicians working to a written rope access plan with a rescue plan in place
Hatch coamings, upper frames, transverse bulkheads and hatch cover undersides cleaned
Spot blasting, rust removal and touch-up coating at height where the scope calls for it
Close visual inspection of upper structure, reported with photographs at position
Work planned around the discharge sequence and the working rules in force at Magdalla
Completion report with before-and-after imagery by hold and by area

Planning the window at Magdalla

The south-west monsoon governs the calendar at Magdalla Port, roughly June to September. Swell and reduced surface visibility close most open-water work on this coast for the duration, and the weeks either side are unreliable rather than unusable. Some vessels sit and some turn straight round, so the plan is agreed against the actual call rather than a standard package: a shore gang alongside where there is time, a riding crew on the outward passage where there is not.

Teams mobilise via Surat (STV) or Vadodara (BDQ), so give us the ETA as early as you have it — the travel is the flexible part, the approvals and the working window are not.

What we typically find at Magdalla

Scrap and steel are the difficult residues at Magdalla rather than the bulk: loose metal, cut wire and dunnage in the frames and bilge wells, which has to be picked out by hand before any washing is worth starting. Holds here are smaller, which at least keeps the job proportionate to the tonnage.

The standing residues at Magdalla Port are coal, steel and scrap, timber — the dusty, abrasive kind that films every surface and packs into frames, brackets and the tank-top margins. Anything following into a clean or food-grade cargo needs the full sequence: sweep, wash, rinse and dry, not a hose down.

Standard scope of work

Included as standard on every rope access hold cleaning attendance, wherever the vessel is. Anything outside it is quoted separately and flagged before mobilisation, never added afterwards.

Upper frame and bulkhead cleaning: Washing and residue removal on upper side frames, brackets, stiffeners and transverse bulkheads that deck-level equipment cannot reach.
Hold overhead and hatch underside: Cleaning of the hold overhead, hatch cover undersides and coaming internals, where cargo dust and previous-cargo residue routinely accumulate.
Close-up visual inspection: Structural condition, coating breakdown and corrosion recorded at height with photographs, giving you inspection-quality data as a by-product of the clean.
Spot preparation and coating: Localised descaling, surface preparation and touch-up coating applied at height, so identified breakdown is treated in the same mobilisation.
Rigging, rescue and supervision: Every work site is rigged with independent working and backup lines under a Level 3 supervisor, with a documented rescue plan in place before the first descent.

Full Hold Cleaning Rope Access service details

How we deliver it at Magdalla

1
Scope and vessel details
Tell us the vessel, her particulars, the last and next cargo and the window at Magdalla. We come back with a defined scope, a crew size and a duration we will stand behind. Where the conditions here will not support what has been asked for, we say so at this stage rather than after mobilisation.
2
Approvals and waste routing
Access and working approval is arranged with Gujarat Maritime Board and the terminal, and the disposal route for residues and washings is fixed before the gang boards — MARPOL Annex V compliance is a documented chain at Magdalla, not an assurance. Where reception is limited, the plan changes rather than the paperwork.
3
Mobilisation to Magdalla
Gangs, pumps, chemicals and equipment mobilise via Surat (STV) or Vadodara (BDQ). Where a vessel is also calling at Hazira, one mobilisation is normally sized to cover both.
4
Entry, sequencing and the work
Enclosed-space entry runs to the vessel's own permit system, with a fresh gas test before every entry and after every break. Gas testing, standby cover and continuous supervision run throughout, and progress is reported hold by hold rather than only at the end.
5
Report and handover
A completion report covering rope access hold cleaning is issued with before-and-after imagery, hold by hold and anything found that you should know about. The findings are discussed with the vessel rather than emailed and forgotten.

Magdalla Port at a glance

UN/LOCODE: INMDA
Port type: State Port
State: Gujarat
Country: India
Water body: Tapi estuary, Gulf of Khambhat
Port authority: Gujarat Maritime Board
Main cargoes: Coal, Steel and scrap, Timber, Edible oil, General cargo
Crew mobilisation: Surat (STV) / Vadodara (BDQ)
Services here: Hull Cleaning, Hold Cleaning and Tank Cleaning

Frequently asked — Rope Access Hold Cleaning at Magdalla

Do you provide rope access hold cleaning at Magdalla Port?

Yes. Cleanship Marine works Magdalla Port (INMDA) in Gujarat, India, covering the river jetties and outer anchorage. Teams mobilise via Surat (STV) or Vadodara (BDQ) with the full spread.

Can rope access hold cleaning be done while the vessel works cargo at Magdalla?

It depends on the call. Where the vessel has time, a shore gang works the holds alongside as they empty; where she turns straight round, a riding crew completes them on the passage. The vessel stays on hire throughout, and there is no diversion and no dry dock. We scope against the conditions at Magdalla and tell you honestly whether the window you have is enough.

How are hold washings and cargo residues disposed of at Magdalla?

To MARPOL Annex V, through the reception route agreed with Gujarat Maritime Board and the terminal before the gang boards. Residues, sweepings and washing water are tracked from the hold to reception with documentation, so the vessel has a record rather than an assurance. Where reception capacity at Magdalla is limited, we change the plan rather than the paperwork.

Where is the work done at Magdalla — alongside, at anchorage or on passage?

Work here runs both alongside and at anchorage depending on the call, and on the passage out where neither gives enough time.

Which vessels do you carry out rope access hold cleaning on at Magdalla?

Handysize bulk carriers, General cargo ships and Coastal tankers — the traffic at Magdalla Port runs to coal, steel and scrap, timber, so those are the profiles we see most. The scope is sized to the vessel, not to a standard package.

How quickly can a team mobilise to Magdalla?

Crews and equipment mobilise via Surat (STV) or Vadodara (BDQ). Give us the ETA and the window and we will confirm what is achievable rather than promise a date we cannot hold. Where the vessel also calls at Hazira or Dahej, one mobilisation is often sized to cover both.

What does rope access hold cleaning at Magdalla cost?

It depends on the number of holds, the residue from the last cargo, the standard the next fixture demands and how much time the call at Magdalla actually gives. We would rather scope it properly and give you a specific figure than quote a headline rate that changes once the work starts. Send the details and the window at Magdalla and you get a scoped price, usually the same working day.

Get in touch