Rope Access Hold Cleaning at Muldwarka Port
The upper hold reached without staging
Get a quote
Tell us the vessel, the port and the window. Scoped reply, usually the same working day.
Cleanship Marine provides IRATA rope access teams at Muldwarka Port, Gujarat, to clean, inspect and treat the upper areas of cargo holds — hatch coamings, upper frames, transverse bulkheads and the underside of hatch covers — without staging or cherry pickers.
The top third of a cargo hold is where staging costs, schedule and risk all concentrate, and it is the part a deck-level gang cannot reach properly. Rope access removes the scaffolding from the equation entirely. At Muldwarka it also fits the schedule: the upper hold can be worked from ropes while the lower hold is still discharging, so the two do not queue behind each other.
What it gets you
- Upper hold areas actually reached and cleaned, not just the parts a gang can stand on
- No staging cost, no cherry picker and no lost days erecting and striking it
- Structural condition at height inspected while the technicians are already there
- Fewer people working at height, under a written plan with a rescue capability
Working conditions at Muldwarka
Most of the work at this port happens at the anchorage, simply because that is where vessels spend their time. The south-west monsoon sets the outer limits of the calendar, roughly June to September, and it affects the anchorage far more than the berth. Access approval runs through Gujarat Maritime Board and the terminal, and the disposal route for residues and washings is fixed before the gang boards rather than found afterwards.
- Where we work
- Jetty berth · Offshore anchorage
- Vessels we see here
- Coastal cement carriers · Handysize bulk carriers · Barges and tugs
What we do at Muldwarka
- IRATA-certified technicians working to a written rope access plan with a rescue plan in place
- Hatch coamings, upper frames, transverse bulkheads and hatch cover undersides cleaned
- Spot blasting, rust removal and touch-up coating at height where the scope calls for it
- Close visual inspection of upper structure, reported with photographs at position
- Work planned around the discharge sequence and the working rules in force at Muldwarka
- Completion report with before-and-after imagery by hold and by area
Planning the window at Muldwarka
The south-west monsoon governs the calendar at Muldwarka Port, roughly June to September. Swell and reduced surface visibility close most open-water work on this coast for the duration, and the weeks either side are unreliable rather than unusable. Waiting time is the opportunity here. Vessels sit at this port for extended periods, so holds can be worked properly and to a standard rather than rushed between grabs — and a gang put on board during the wait costs the vessel nothing in schedule.
Teams mobilise via Diu (DIU) or Rajkot (RAJ), so give us the ETA as early as you have it — the travel is the flexible part, the approvals and the working window are not.
What we typically find at Muldwarka
Cement and clinker are the residues here and they are the unforgiving kind, because they set. A hold washed late after a clinker cargo needs mechanical removal rather than a hose, so on the short coastal runs out of Muldwarka the cleaning is planned for immediately after discharge, never for the next port.
The standing residues at Muldwarka Port are cement and clinker, coal, gypsum — the dusty, abrasive kind that films every surface and packs into frames, brackets and the tank-top margins. Anything following into a clean or food-grade cargo needs the full sequence: sweep, wash, rinse and dry, not a hose down.
Standard scope of work
Included as standard on every rope access hold cleaning attendance, wherever the vessel is. Anything outside it is quoted separately and flagged before mobilisation, never added afterwards.
- Upper frame and bulkhead cleaning
- Washing and residue removal on upper side frames, brackets, stiffeners and transverse bulkheads that deck-level equipment cannot reach.
- Hold overhead and hatch underside
- Cleaning of the hold overhead, hatch cover undersides and coaming internals, where cargo dust and previous-cargo residue routinely accumulate.
- Close-up visual inspection
- Structural condition, coating breakdown and corrosion recorded at height with photographs, giving you inspection-quality data as a by-product of the clean.
- Spot preparation and coating
- Localised descaling, surface preparation and touch-up coating applied at height, so identified breakdown is treated in the same mobilisation.
- Rigging, rescue and supervision
- Every work site is rigged with independent working and backup lines under a Level 3 supervisor, with a documented rescue plan in place before the first descent.
How we deliver it at Muldwarka
- 1
Scope and vessel details
Tell us the vessel, her particulars, the last and next cargo and the window at Muldwarka. We come back with a defined scope, a crew size and a duration we will stand behind. Where the conditions here will not support what has been asked for, we say so at this stage rather than after mobilisation.
- 2
Approvals and waste routing
Access and working approval is arranged with Gujarat Maritime Board and the terminal, and the disposal route for residues and washings is fixed before the gang boards — MARPOL Annex V compliance is a documented chain at Muldwarka, not an assurance. Where reception is limited, the plan changes rather than the paperwork.
- 3
Mobilisation to Muldwarka
Gangs, pumps, chemicals and equipment mobilise via Diu (DIU) or Rajkot (RAJ). Where a vessel is also calling at Pipavav, one mobilisation is normally sized to cover both.
- 4
Entry, sequencing and the work
Enclosed-space entry runs to the vessel's own permit system, with a fresh gas test before every entry and after every break. Gas testing, standby cover and continuous supervision run throughout, and progress is reported hold by hold rather than only at the end.
- 5
Report and handover
A completion report covering rope access hold cleaning is issued with before-and-after imagery, hold by hold and anything found that you should know about. The findings are discussed with the vessel rather than emailed and forgotten.
Muldwarka Port at a glance
- UN/LOCODE
- INMDK
- Port type
- State Port
- State
- Gujarat
- Country
- India
- Water body
- Arabian Sea off Saurashtra
- Port authority
- Gujarat Maritime Board
- Main cargoes
- Cement and clinker, Coal, Gypsum
- Crew mobilisation
- Diu (DIU) / Rajkot (RAJ)
- Services here
- Hull Cleaning and Hold Cleaning
Frequently asked — Rope Access Hold Cleaning at Muldwarka
Do you provide rope access hold cleaning at Muldwarka Port?
Yes. Cleanship Marine works Muldwarka Port (INMDK) in Gujarat, India, covering the jetty berth and offshore anchorage. Teams mobilise via Diu (DIU) or Rajkot (RAJ) with the full spread.
Can rope access hold cleaning be done while the vessel works cargo at Muldwarka?
Yes, and the better answer here is usually to start before discharge finishes. Vessels wait at this port, so a gang boards during the wait and works the holds as they empty — no port time is lost, because the vessel was not sailing anyway. The vessel stays on hire throughout, and there is no diversion and no dry dock. We scope against the conditions at Muldwarka and tell you honestly whether the window you have is enough.
How are hold washings and cargo residues disposed of at Muldwarka?
To MARPOL Annex V, through the reception route agreed with Gujarat Maritime Board and the terminal before the gang boards. Residues, sweepings and washing water are tracked from the hold to reception with documentation, so the vessel has a record rather than an assurance. Where reception capacity at Muldwarka is limited, we change the plan rather than the paperwork.
Where is the work done at Muldwarka — alongside, at anchorage or on passage?
Most of the work at this port happens at the anchorage, simply because that is where vessels spend their time.
Which vessels do you carry out rope access hold cleaning on at Muldwarka?
Coastal cement carriers, Handysize bulk carriers, Barges and tugs — the traffic at Muldwarka Port runs to cement and clinker, coal, gypsum, so those are the profiles we see most. The scope is sized to the vessel, not to a standard package.
How quickly can a team mobilise to Muldwarka?
Crews and equipment mobilise via Diu (DIU) or Rajkot (RAJ). Give us the ETA and the window and we will confirm what is achievable rather than promise a date we cannot hold. Where the vessel also calls at Pipavav or Porbandar, one mobilisation is often sized to cover both.
What does rope access hold cleaning at Muldwarka cost?
It depends on the number of holds, the residue from the last cargo, the standard the next fixture demands and how much time the call at Muldwarka actually gives. We would rather scope it properly and give you a specific figure than quote a headline rate that changes once the work starts. Send the details and the window at Muldwarka and you get a scoped price, usually the same working day.
Rope Access Hold Cleaning at Muldwarka Port.
Tell us the vessel, her ETA at Muldwarka and the window. You get a scope, a crew size and an honest duration — usually the same working day.