Cargo Hold Cleaning (Shore Gang) at Mormugao Port
Holds ready for the next fixture before the vessel sails
Get a quote
Tell us the vessel, the port and the window. Scoped reply, usually the same working day.
Cleanship Marine puts shore gangs on board at Mormugao Port, Goa, to clean cargo holds between fixtures — sweeping, washing, rinsing and drying to the standard the next cargo demands, worked at the inner harbour berths and breakwater berths.
Mormugao is Goa's major port, historically an iron ore export terminal and now working coal imports, containers and a growing cruise call list. The mix of large bulk carriers and river barge traffic means underwater work here ranges from Capesize hulls down to small craft propellers.
What it gets you
- Holds presented to the standard the next fixture actually requires
- Inspection failures and the resulting demurrage avoided
- Residue and washings disposed of to MARPOL Annex V rather than left as the master's problem
- Crew kept on their own work instead of on cleaning duty
Working conditions at Mormugao
Work here runs both alongside and at anchorage depending on the call, and on the passage out where neither gives enough time. The south-west monsoon sets the outer limits of the calendar, roughly June to September, and it affects the anchorage far more than the berth. Access approval runs through Mormugao Port Authority and the terminal, and the disposal route for residues and washings is fixed before the gang boards rather than found afterwards.
- Where we work
- Inner harbour berths · Breakwater berths · Anchorage
- Vessels we see here
- Panamax and Capesize bulk carriers · Container ships · Cruise ships · Ore barges and tugs
What we do at Mormugao
- Sweeping and removal of cargo residues, dunnage and lashing waste from tank tops, frames and brackets
- Fresh or sea water washing with the correct chemical treatment for the residue found, followed by a fresh water rinse
- Bilge wells, strum boxes, bilge lines and hold ladders cleaned and tested
- Drying and ventilation so holds pass inspection rather than merely look clean
- Residue and washing water handled to MARPOL Annex V requirements and the disposal rules in force at Mormugao
- Hold-by-hold photographic record and a completion report ahead of the inspection
Planning the window at Mormugao
The south-west monsoon governs the calendar at Mormugao Port, roughly June to September. Swell and reduced surface visibility close most open-water work on this coast for the duration, and the weeks either side are unreliable rather than unusable. Some vessels sit and some turn straight round, so the plan is agreed against the actual call rather than a standard package: a shore gang alongside where there is time, a riding crew on the outward passage where there is not.
Teams mobilise via Goa (GOI), so give us the ETA as early as you have it — the travel is the flexible part, the approvals and the working window are not.
What we typically find at Mormugao
Mormugao's iron ore heritage still shows in the holds: ore fines and red staining are the standing job, now alongside imported coal. Barge-fed loading extends the exposure, so the fines get further into the frames than a single berth call would ever put them.
The standing residues at Mormugao Port are coal, iron ore and containers — the dusty, abrasive kind that films every surface and packs into frames, brackets and the tank-top margins. Anything following into a clean or food-grade cargo needs the full sequence: sweep, wash, rinse and dry, not a hose down.
Standard scope of work
Included as standard on every cargo hold cleaning attendance, wherever the vessel is. Anything outside it is quoted separately and flagged before mobilisation, never added afterwards.
- Sweeping and residue removal
- Full manual and mechanical sweep of tank tops, hoppers, brackets and frames, with residues bagged for landing ashore in line with MARPOL Annex V.
- High-pressure washing
- Fresh or sea water washing at working pressures suited to the coating condition, covering tank top, hopper plating, side frames, bulkheads and the underside of hatch covers.
- Chemical treatment
- Application of marine-approved, biodegradable degreasers and hold cleaners where previous cargoes have left oily, staining or odour-bearing residues.
- Rinsing and drying
- Fresh water rinse to remove salt and chemical traces, followed by forced drying and bilge drying so holds present dry, odour-free and free of loose scale.
- Bilge wells and hatch coamings
- Bilge wells cleaned, strainers cleared and non-return valves tested; coamings, drain channels and compression bars cleaned so hatch covers seal correctly.
How we deliver it at Mormugao
- 1
Scope and vessel details
Tell us the vessel, her particulars, the last and next cargo and the window at Mormugao. We come back with a defined scope, a crew size and a duration we will stand behind. Where the conditions here will not support what has been asked for, we say so at this stage rather than after mobilisation.
- 2
Approvals and waste routing
Access and working approval is arranged with Mormugao Port Authority and the terminal, and the disposal route for residues and washings is fixed before the gang boards — MARPOL Annex V compliance is a documented chain at Mormugao, not an assurance. Where reception is limited, the plan changes rather than the paperwork.
- 3
Mobilisation to Mormugao
Gangs, pumps, chemicals and equipment mobilise via Goa (GOI). Where a vessel is also calling at Karwar, one mobilisation is normally sized to cover both.
- 4
Entry, sequencing and the work
Enclosed-space entry runs to the vessel's own permit system, with a fresh gas test before every entry and after every break. Gas testing, standby cover and continuous supervision run throughout, and progress is reported hold by hold rather than only at the end.
- 5
Report and handover
A completion report covering cargo hold cleaning is issued with before-and-after imagery, hold by hold and anything found that you should know about. The findings are discussed with the vessel rather than emailed and forgotten.
Mormugao Port at a glance
- UN/LOCODE
- INMRM
- Port type
- Major Port
- State
- Goa
- Country
- India
- Water body
- Arabian Sea at the mouth of the Zuari
- Port authority
- Mormugao Port Authority
- Main cargoes
- Coal, Iron ore, Containers, POL, Cruise
- Crew mobilisation
- Goa (GOI)
- Services here
- Hull Cleaning, Hold Cleaning and Tank Cleaning
Frequently asked — Cargo Hold Cleaning at Mormugao
Do you provide cargo hold cleaning at Mormugao Port?
Yes. Cleanship Marine works Mormugao Port (INMRM) in Goa, India, covering the inner harbour berths, breakwater berths and anchorage. Teams mobilise via Goa (GOI) with the full spread.
Can cargo hold cleaning be done while the vessel works cargo at Mormugao?
It depends on the call. Where the vessel has time, a shore gang works the holds alongside as they empty; where she turns straight round, a riding crew completes them on the passage. The vessel stays on hire throughout, and there is no diversion and no dry dock. We scope against the conditions at Mormugao and tell you honestly whether the window you have is enough.
How are hold washings and cargo residues disposed of at Mormugao?
To MARPOL Annex V, through the reception route agreed with Mormugao Port Authority and the terminal before the gang boards. Residues, sweepings and washing water are tracked from the hold to reception with documentation, so the vessel has a record rather than an assurance. Where reception capacity at Mormugao is limited, we change the plan rather than the paperwork.
Where is the work done at Mormugao — alongside, at anchorage or on passage?
Work here runs both alongside and at anchorage depending on the call, and on the passage out where neither gives enough time.
Which vessels do you carry out cargo hold cleaning on at Mormugao?
Panamax and Capesize bulk carriers, Container ships, Cruise ships, Ore barges and tugs — the traffic at Mormugao Port runs to coal, iron ore and containers, so those are the profiles we see most. The scope is sized to the vessel, not to a standard package.
How quickly can a team mobilise to Mormugao?
Crews and equipment mobilise via Goa (GOI). Give us the ETA and the window and we will confirm what is achievable rather than promise a date we cannot hold. Where the vessel also calls at Karwar or Panaji, one mobilisation is often sized to cover both.
What does cargo hold cleaning at Mormugao cost?
It depends on the number of holds, the residue from the last cargo, the standard the next fixture demands and how much time the call at Mormugao actually gives. We would rather scope it properly and give you a specific figure than quote a headline rate that changes once the work starts. Send the details and the window at Mormugao and you get a scoped price, usually the same working day.
Cargo Hold Cleaning (Shore Gang) at Mormugao Port.
Tell us the vessel, her ETA at Mormugao and the window. You get a scope, a crew size and an honest duration — usually the same working day.