Propeller Polishing at Jubail Port
Mirror finish, measurably lower fuel burn
Get a quote
Tell us the vessel, the port and the window. Scoped reply, usually the same working day.
Cleanship Marine carries out underwater propeller super polishing at Jubail Port, Eastern Province. Divers work the blades through a multi-stage sequence to a Class A mirror finish, removing fouling, calcareous deposits and accumulated surface roughness while the vessel lies alongside or at anchor.
The propeller is the highest-leverage surface on any vessel calling at Jubail: it runs at high relative velocity, so roughness there costs disproportionately more than the same roughness spread over the hull. For the chemical and product tankers, LPG carriers, bulk carriers working this port, polishing is the shortest route to a measurable fuel saving.
What it gets you
- Blade roughness removed where it costs the most, at the highest-velocity surface on the vessel
- Propeller efficiency restored between dockings without off-hire
- Cavitation erosion and edge damage documented before it becomes a repair item
- A finish record that supports hull and propeller performance monitoring
Working conditions at Jubail
Jubail is a purpose-built industrial port serving the largest petrochemical complex in the region, so access is controlled and the permit chain runs through the terminal and the Royal Commission as well as the port. That is a lead time, not a formality. The harbour is sheltered and alongside work is straightforward once cleared; the shamal governs the anchorage and summer heat governs anything done inside a tank.
- Where we work
- Chemical and liquid berths · General cargo quays · Outer anchorage
- Vessels we see here
- Chemical and product tankers · LPG carriers · Bulk carriers · General cargo and project vessels
What we do at Jubail
- Blade condition assessment covering both faces, the leading and trailing edges and the tips
- Multi-stage polishing sequence worked down to a Class A mirror finish
- Boss, hub and fairing cone cleaned, with rope guard and seal area inspected
- Edge damage, cavitation erosion and any deformation photographed and reported rather than polished over
- Diving permission cleared with Mawani and the Royal Commission for Jubail, and the shaft confirmed immobilised with the master before the dive
- Before-and-after video and a written finish record for the performance file
Planning the window at Jubail
The shamal governs the calendar at Jubail Port, through the winter months and again in early summer. The shamal is a wind and sea-state problem rather than a rain one: it builds short, steep seas across the shallow Gulf that stop anchorage work while berths stay usable. Because the harbour is sheltered, work here normally runs alongside or at a protected anchorage and can proceed in parallel with cargo operations rather than competing with them for the berth window.
Work is taken at the chemical and liquid berths, general cargo quays, outer anchorage, and which of those a vessel ends up at changes the dive plan more than the season does. Teams mobilise via Dammam (DMM), so give us the ETA as early as you have it — the travel is the flexible part, the approvals and the working window are not.
What we typically find at Jubail
Dry bulk handling here puts cargo dust into the water around the berths and anchorage. It settles on horizontal surfaces and packs into sea chest gratings and inlet openings, so inlet and grating clearance is routinely a larger part of the job at Jubail than owners budget for.
Shelter is a mixed blessing for a hull. The same calm that makes the port easy to work in is still water, and still water grows fouling faster than an exposed berth does.
Standard scope of work
Included as standard on every propeller polishing attendance, wherever the vessel is. Anything outside it is quoted separately and flagged before mobilisation, never added afterwards.
- Deposit removal
- Calcareous growth, shell and hard deposits removed from both blade faces without gouging or scoring the blade surface.
- Progressive polishing
- Successive abrasive grades work the blade from rough to fine, finishing at a Class A mirror surface across the full blade area.
- Edge finishing
- Leading and trailing edges dressed to restore profile and remove the roughness that seeds cavitation.
- Boss and hub
- Boss, hub and rope guard cleaned, with stern tube seal condition inspected and reported.
How we deliver it at Jubail
- 1
Scope and vessel details
Tell us the vessel, her particulars, the coating specification and the window at Jubail. We come back with a defined scope, a crew size and a duration we will stand behind. Where the conditions here will not support what has been asked for, we say so at this stage rather than after mobilisation.
- 2
Permits and approvals
Mawani and the Royal Commission for Jubail runs a statutory permit process here, so the lead time is real and the application goes in early rather than on arrival. Diving permission, terminal approval and any environmental clearance for in-water work are handled by us, not left with the agent to chase.
- 3
Mobilisation to Jubail
Divers, compressors, brush carts and cameras mobilise via Dammam (DMM). Where a vessel is also calling at Dammam, one mobilisation is normally sized to cover both.
- 4
Safety setup and the dive
The vessel is secured for diving — main engine, shaft and thrusters immobilised, sea suctions confirmed shut, permit agreed with the master. Teams work under surface supervision with continuous diver communications and video throughout.
- 5
Report and handover
A completion report covering propeller polishing is issued with before-and-after imagery, coating and anode condition and anything found that you should know about. The findings are discussed with the vessel rather than emailed and forgotten.
Jubail Port at a glance
- UN/LOCODE
- SAJBI
- Port type
- Major Port
- State
- Eastern Province
- Country
- Saudi Arabia
- Water body
- Arabian Gulf
- Port authority
- Mawani and the Royal Commission for Jubail
- Main cargoes
- Petrochemicals, Liquid chemicals, Sulphur, Containers, Project cargo and steel
- Crew mobilisation
- Dammam (DMM)
- Services here
- Hull Cleaning, Hold Cleaning and Tank Cleaning
Frequently asked — Propeller Polishing at Jubail
Do you provide propeller polishing at Jubail Port?
Yes. Cleanship Marine works Jubail Port (SAJBI) in Eastern Province, Saudi Arabia, covering the chemical and liquid berths, general cargo quays, outer anchorage. Teams mobilise via Dammam (DMM) with the full spread.
Can propeller polishing be done while the vessel works cargo at Jubail?
Yes, in most cases. The harbour is sheltered enough that divers work alongside while cargo operations continue, and neither holds the other up. The vessel stays on hire throughout, and there is no diversion and no dry dock. We scope against the conditions at Jubail and tell you honestly whether the window you have is enough.
Do you need a diving permit from Mawani and the Royal Commission for Jubail?
Yes, and we obtain it. Diving permission from Mawani and the Royal Commission for Jubail, terminal approval where the berth requires it, and any environmental clearance for in-water work are arranged as part of the job rather than left with the agent. The master's permit to work and the immobilisation of machinery are agreed on board before anyone enters the water.
What is underwater visibility like at Jubail?
Visibility at Jubail Port is moderate, and it drops further around active bulk handling and after heavy rain, and the shamal sets the outer limits of the calendar. How the tide and sea state shape the dive plan is set out in full in the working-conditions section on this page.
Which vessels do you carry out propeller polishing on at Jubail?
Chemical and product tankers, LPG carriers, Bulk carriers, General cargo and project vessels — the traffic at Jubail Port runs to petrochemicals, liquid chemicals and sulphur, so those are the profiles we see most. The scope is sized to the vessel, not to a standard package.
How quickly can a team mobilise to Jubail?
Divers and equipment mobilise via Dammam (DMM). Give us the ETA and the window and we will confirm what is achievable rather than promise a date we cannot hold. Where the vessel also calls at Dammam or Jeddah, one mobilisation is often sized to cover both.
What does propeller polishing at Jubail cost?
It depends on the vessel's dimensions and wetted area, the fouling state found, the coating specification and the working window available at Jubail. We would rather scope it properly and give you a specific figure than quote a headline rate that changes once the work starts. Send the details and the window at Jubail and you get a scoped price, usually the same working day.
Propeller Polishing at Jubail Port.
Tell us the vessel, her ETA at Jubail and the window. You get a scope, a crew size and an honest duration — usually the same working day.