Underwater Hull Cleaning at Ruwais Port
Full hull cleaned in the water, vessel stays on hire
Get a quote
Tell us the vessel, the port and the window. Scoped reply, usually the same working day.
Cleanship Marine provides underwater hull cleaning at Ruwais Port, Abu Dhabi, working the crude loading berths and product jetties. Commercial dive teams remove slime, weed and shell growth from the vertical sides, flat bottom, bilge keels, sea chests and niche areas with the vessel afloat and on hire — no dry dock, no diversion, no off-hire.
Ruwais is the UAE's largest refining and petrochemical export complex, loading crude, refined products, LPG and sulphur to dedicated berths. The tonnage is large and specialised, and the port calls are governed end to end by terminal windows.
What it gets you
- Hydrodynamic smoothness restored before fouling reaches the calcareous stage that damages coating
- Fuel and emissions penalty from drag reduced without taking the vessel off hire
- Documented condition record for the technical file and the next docking specification
- Sea chests and inlets cleared, protecting cooling water flow
Working conditions at Ruwais
Ruwais is a refinery and petrochemical complex with dedicated loading berths, so it is sheltered and the working constraint is the terminal, not the weather. Access is controlled and the permit chain runs through the terminal operator as well as the port — for a gas or crude berth that is a lead time, not a formality. Gulf water here is shallow, warm and hypersaline with moderate visibility.
- Where we work
- Crude loading berths · Product jetties · Sulphur berth
- Vessels we see here
- VLCC and Suezmax crude tankers · Product and chemical tankers · LPG carriers · Sulphur bulk carriers
What we do at Ruwais
- Pre-clean fouling survey to establish coverage, growth type and coating condition before any tool touches the hull
- Brush cart cleaning of the flat bottom and vertical sides, with brush hardness selected against your antifouling specification
- Hand cleaning of bilge keels, rudder, stern frame, thruster tunnels, anodes and the niches a cart cannot follow
- Sea chest gratings and inlet openings cleared of growth and debris to restore cooling water flow
- Diving permission cleared with AD Ports Group and the terminal operator and the terminal before mobilisation
- Before-and-after video and stills, with a written report on coating condition and anode wastage
Planning the window at Ruwais
The shamal governs the calendar at Ruwais Port, through the winter months and again in early summer. The shamal is a wind and sea-state problem rather than a rain one: it builds short, steep seas across the shallow Gulf that stop anchorage work while berths stay usable. Because the harbour is sheltered, work here normally runs alongside or at a protected anchorage and can proceed in parallel with cargo operations rather than competing with them for the berth window.
Work is taken at the crude loading berths, product jetties and sulphur berth, and which of those a vessel ends up at changes the dive plan more than the season does. Teams mobilise via Abu Dhabi (AUH) or Dubai (DXB), so give us the ETA as early as you have it — the travel is the flexible part, the approvals and the working window are not.
What we typically find at Ruwais
Dry bulk handling here puts cargo dust into the water around the berths and anchorage. It settles on horizontal surfaces and packs into sea chest gratings and inlet openings, so inlet and grating clearance is routinely a larger part of the job at Ruwais than owners budget for.
Shelter is a mixed blessing for a hull. The same calm that makes the port easy to work in is still water, and still water grows fouling faster than an exposed berth does.
Standard scope of work
Included as standard on every underwater hull cleaning attendance, wherever the vessel is. Anything outside it is quoted separately and flagged before mobilisation, never added afterwards.
- Fouling survey
- A pre-clean dive establishes fouling type, coverage and severity, and confirms coating condition so the correct tooling is selected.
- Flat bottom and vertical sides
- Brush cart cleaning of large areas, removing slime, weed and shell growth to restore surface smoothness.
- Niche areas
- Hand cleaning of bilge keels, bow thruster tunnels, rudder, stern frame, anodes and other niche areas where fouling concentrates.
- Sea chests and gratings
- Sea chest gratings and inlet openings cleared of growth and debris to restore cooling water flow.
- Documentation
- Underwater video and stills before and after, with a written report covering coating condition and anode wastage.
How we deliver it at Ruwais
- 1
Scope and vessel details
Tell us the vessel, her particulars, the coating specification and the window at Ruwais. We come back with a defined scope, a crew size and a duration we will stand behind. Where the conditions here will not support what has been asked for, we say so at this stage rather than after mobilisation.
- 2
Permits and approvals
Diving permission is obtained from AD Ports Group and the terminal operator, along with terminal approval where the berth requires it and any environmental clearance for in-water work. This is handled by us, not left with the agent to chase.
- 3
Mobilisation to Ruwais
Divers, compressors, brush carts and cameras mobilise via Abu Dhabi (AUH) or Dubai (DXB). Where a vessel is also calling at Khalifa Port, one mobilisation is normally sized to cover both.
- 4
Safety setup and the dive
The vessel is secured for diving — main engine, shaft and thrusters immobilised, sea suctions confirmed shut, permit agreed with the master. Teams work under surface supervision with continuous diver communications and video throughout.
- 5
Report and handover
A completion report covering underwater hull cleaning is issued with before-and-after imagery, coating and anode condition and anything found that you should know about. The findings are discussed with the vessel rather than emailed and forgotten.
Ruwais Port at a glance
- UN/LOCODE
- AERUW
- Port type
- Private Port
- Emirate
- Abu Dhabi
- Country
- United Arab Emirates
- Water body
- Arabian Gulf
- Port authority
- AD Ports Group and the terminal operator
- Main cargoes
- Crude oil, Refined products, Petrochemicals, LPG, Sulphur
- Crew mobilisation
- Abu Dhabi (AUH) / Dubai (DXB)
- Services here
- Hull Cleaning, Hold Cleaning and Tank Cleaning
Frequently asked — Underwater Hull Cleaning at Ruwais
Do you provide underwater hull cleaning at Ruwais Port?
Yes. Cleanship Marine works Ruwais Port (AERUW) in Abu Dhabi, United Arab Emirates, covering the crude loading berths, product jetties and sulphur berth. Teams mobilise via Abu Dhabi (AUH) or Dubai (DXB) with the full spread.
Can underwater hull cleaning be done while the vessel works cargo at Ruwais?
Yes, in most cases. The harbour is sheltered enough that divers work alongside while cargo operations continue, and neither holds the other up. The vessel stays on hire throughout, and there is no diversion and no dry dock. We scope against the conditions at Ruwais and tell you honestly whether the window you have is enough.
Do you need a diving permit from AD Ports Group and the terminal operator?
Yes, and we obtain it. Diving permission from AD Ports Group and the terminal operator, terminal approval where the berth requires it, and any environmental clearance for in-water work are arranged as part of the job rather than left with the agent. The master's permit to work and the immobilisation of machinery are agreed on board before anyone enters the water.
What is underwater visibility like at Ruwais?
Visibility at Ruwais Port is moderate, and it drops further around active bulk handling and after heavy rain, and the shamal sets the outer limits of the calendar. How the tide and sea state shape the dive plan is set out in full in the working-conditions section on this page.
Which vessels do you carry out underwater hull cleaning on at Ruwais?
VLCC and Suezmax crude tankers, Product and chemical tankers, LPG carriers, Sulphur bulk carriers — the traffic at Ruwais Port runs to crude oil, refined products and petrochemicals, so those are the profiles we see most. The scope is sized to the vessel, not to a standard package.
How quickly can a team mobilise to Ruwais?
Divers and equipment mobilise via Abu Dhabi (AUH) or Dubai (DXB). Give us the ETA and the window and we will confirm what is achievable rather than promise a date we cannot hold. Where the vessel also calls at Khalifa Port or Zayed Port, one mobilisation is often sized to cover both.
What does underwater hull cleaning at Ruwais cost?
It depends on the vessel's dimensions and wetted area, the fouling state found, the coating specification and the working window available at Ruwais. We would rather scope it properly and give you a specific figure than quote a headline rate that changes once the work starts. Send the details and the window at Ruwais and you get a scoped price, usually the same working day.
Underwater Hull Cleaning at Ruwais Port.
Tell us the vessel, her ETA at Ruwais and the window. You get a scope, a crew size and an honest duration — usually the same working day.