Underwater Hull Cleaning at Tarrafal Port
Full hull cleaned in the water, vessel stays on hire
Get a quote
Tell us the vessel, the port and the window. Scoped reply, usually the same working day.
Cleanship Marine provides underwater hull cleaning at Tarrafal Port, São Nicolau, working the port quay and fishing boat moorings. Commercial dive teams remove slime, weed and shell growth from the vertical sides, flat bottom, bilge keels, sea chests and niche areas with the vessel afloat and on hire — no dry dock, no diversion, no off-hire.
Tarrafal is the main port of São Nicolau and a fishing town above all: the Sucla tuna cannery here is one of the island's largest employers, processing tuna caught in the surrounding waters. Ferries and coasters connect the island to Mindelo and Praia, and the rest of the traffic is the fishing fleet that supplies the cannery.
Tarrafal's working fleet is fishing vessels supplying the tuna cannery, and fishing boats foul differently from cargo ships: they spend long periods slow or stationary on the fishing grounds, and their hulls carry growth that costs them speed and fuel on the run back to port. Cleaning in Tarrafal's deep, clear water close to the port is straightforward, and for a fishing vessel it is usually done between trips so it costs no fishing time.
What it gets you
- Hydrodynamic smoothness restored before fouling reaches the calcareous stage that damages coating
- Fuel and emissions penalty from drag reduced without taking the vessel off hire
- Documented condition record for the technical file and the next docking specification
- Sea chests and inlets cleared, protecting cooling water flow
Working conditions at Tarrafal
Tarrafal is on the south-west coast of São Nicolau, in the lee of the island's mountains, and the sea bed drops away quickly offshore, so there is deep, clear ocean water close to the port. The trade wind is broken by the island but can come down off the high ground in gusts. The port is small and its quay is shared by ferries, coasters and the fishing fleet, so in-water work is fitted around them or done at anchor off the town.
- Where we work
- Port quay · Fishing boat moorings · Anchorage off Tarrafal
- Vessels we see here
- Tuna fishing vessels · Inter-island ferries · General cargo coasters
What we do at Tarrafal
- Pre-clean fouling survey to establish coverage, growth type and coating condition before any tool touches the hull
- Brush cart cleaning of the flat bottom and vertical sides, with brush hardness selected against your antifouling specification
- Hand cleaning of bilge keels, rudder, stern frame, thruster tunnels, anodes and the niches a cart cannot follow
- Sea chest gratings and inlet openings cleared of growth and debris to restore cooling water flow
- Diving permission cleared with ENAPOR – Portos de Cabo Verde and the terminal before mobilisation
- Before-and-after video and stills, with a written report on coating condition and anode wastage
Planning the window at Tarrafal
The trade-wind and swell season governs the calendar at Tarrafal Port, with the strongest trade winds from roughly December to May, and a short rainy season from August to October. The islands sit in open ocean, so a port's exposure depends on which side of its island it faces: the lee-side harbours stay calm while the trade wind blows, but long-period swell from North Atlantic storms reaches the north and west coasts in winter, and the late-summer tropical waves that pass through here can turn into storms. Water clarity here is good by regional standards, so the operation can be properly documented on video as it happens — an advantage that turns a cleaning job into usable condition evidence at no extra mobilisation cost.
Work is taken at the port quay, fishing boat moorings and anchorage off Tarrafal, and which of those a vessel ends up at changes the dive plan more than the season does. Teams mobilise via São Nicolau (SNE) or São Vicente (VXE), so give us the ETA as early as you have it — the travel is the flexible part, the approvals and the working window are not.
What we typically find at Tarrafal
The working fleet here spends most of its life at low speed in warm water, so growth is heavy, mixed and reaches the hard calcareous stage sooner than on deep-sea tonnage. Left too long it starts damaging the coating rather than just slowing the vessel.
Clearer water means the fouling state can be assessed properly before any tooling is selected, and the assessment can be shown to you rather than described.
Standard scope of work
Included as standard on every underwater hull cleaning attendance, wherever the vessel is. Anything outside it is quoted separately and flagged before mobilisation, never added afterwards.
- Fouling survey
- A pre-clean dive establishes fouling type, coverage and severity, and confirms coating condition so the correct tooling is selected.
- Flat bottom and vertical sides
- Brush cart cleaning of large areas, removing slime, weed and shell growth to restore surface smoothness.
- Niche areas
- Hand cleaning of bilge keels, bow thruster tunnels, rudder, stern frame, anodes and other niche areas where fouling concentrates.
- Sea chests and gratings
- Sea chest gratings and inlet openings cleared of growth and debris to restore cooling water flow.
- Documentation
- Underwater video and stills before and after, with a written report covering coating condition and anode wastage.
How we deliver it at Tarrafal
- 1
Scope and vessel details
Tell us the vessel, her particulars, the coating specification and the window at Tarrafal. We come back with a defined scope, a crew size and a duration we will stand behind. Where the conditions here will not support what has been asked for, we say so at this stage rather than after mobilisation.
- 2
Permits and approvals
ENAPOR – Portos de Cabo Verde approves the work alongside the local harbour master, and at a state port that conversation is quicker but less formal — it is worth having in writing. Diving permission, terminal approval and any environmental clearance for in-water work are handled by us, not left with the agent to chase.
- 3
Mobilisation to Tarrafal
Divers, compressors, brush carts and cameras mobilise via São Nicolau (SNE) or São Vicente (VXE). Where a vessel is also calling at Mindelo, one mobilisation is normally sized to cover both.
- 4
Safety setup and the dive
The vessel is secured for diving — main engine, shaft and thrusters immobilised, sea suctions confirmed shut, permit agreed with the master. Teams work under surface supervision with continuous diver communications and video throughout.
- 5
Report and handover
A completion report covering underwater hull cleaning is issued with before-and-after imagery, coating and anode condition and anything found that you should know about. The findings are discussed with the vessel rather than emailed and forgotten.
Tarrafal Port at a glance
- UN/LOCODE
- CVTAR
- Port type
- State Port
- Island
- São Nicolau
- Country
- Cape Verde
- Water body
- Atlantic Ocean
- Port authority
- ENAPOR – Portos de Cabo Verde
- Main cargoes
- Fishing catch and canned tuna, General cargo, Food and supplies
- Crew mobilisation
- São Nicolau (SNE) / São Vicente (VXE)
- Services here
- Hull Cleaning
Frequently asked — Underwater Hull Cleaning at Tarrafal
Do you provide underwater hull cleaning at Tarrafal Port?
Yes. Cleanship Marine works Tarrafal Port (CVTAR) in São Nicolau, Cape Verde, covering the port quay, fishing boat moorings and anchorage off Tarrafal. Teams mobilise via São Nicolau (SNE) or São Vicente (VXE) with the full spread.
Do you clean fishing vessel hulls in Tarrafal?
Yes — the fishing fleet is the main in-water customer here. We clean between trips, alongside or at anchor off Tarrafal, so the vessel loses no time on the fishing grounds. The deep, clear water close to the port makes it a quick and well-documented job.
Can underwater hull cleaning be done while the vessel works cargo at Tarrafal?
Yes. Conditions here are good enough that the dive runs alongside cargo operations without either holding the other up, and the work is documented on video as it goes. The vessel stays on hire throughout, and there is no diversion and no dry dock. We scope against the conditions at Tarrafal and tell you honestly whether the window you have is enough.
Do you need a diving permit from ENAPOR – Portos de Cabo Verde?
Yes, and we obtain it. Diving permission from ENAPOR – Portos de Cabo Verde, terminal approval where the berth requires it, and any environmental clearance for in-water work are arranged as part of the job rather than left with the agent. The master's permit to work and the immobilisation of machinery are agreed on board before anyone enters the water.
What is underwater visibility like at Tarrafal?
Visibility at Tarrafal Port is very good, with deep, clear ocean water close to the port and no river runoff, and the trade-wind and swell season sets the outer limits of the calendar. How the tide and sea state shape the dive plan is set out in full in the working-conditions section on this page.
Which vessels do you carry out underwater hull cleaning on at Tarrafal?
Tuna fishing vessels, Inter-island ferries and General cargo coasters — the traffic at Tarrafal Port runs to fishing catch and canned tuna, general cargo, food and supplies, so those are the profiles we see most. The scope is sized to the vessel, not to a standard package.
How quickly can a team mobilise to Tarrafal?
Divers and equipment mobilise via São Nicolau (SNE) or São Vicente (VXE). Give us the ETA and the window and we will confirm what is achievable rather than promise a date we cannot hold. Where the vessel also calls at Mindelo or Palmeira, one mobilisation is often sized to cover both.
What does underwater hull cleaning at Tarrafal cost?
It depends on the vessel's dimensions and wetted area, the fouling state found, the coating specification and the working window available at Tarrafal. We would rather scope it properly and give you a specific figure than quote a headline rate that changes once the work starts. Send the details and the window at Tarrafal and you get a scoped price, usually the same working day.
Underwater Hull Cleaning at Tarrafal Port.
Tell us the vessel, her ETA at Tarrafal and the window. You get a scope, a crew size and an honest duration — usually the same working day.