Thruster Cleaning & Polishing at Ennore Port
Full thrust restored when you need it most
Get a quote
Tell us the vessel, the port and the window. Scoped reply, usually the same working day.
Cleanship Marine cleans and polishes bow and stern thrusters at Ennore Port, Tamil Nadu. Divers clear the full tunnel bore, polish the blades and hub, and clear the gratings, restoring the manoeuvring thrust that quietly disappears while a vessel sits idle.
Thruster tunnels are the worst fouling trap on a hull — sheltered, still and almost never inspected. That matters more than usual at Ennore, where coal and car carrier traffic north of Chennai keeps vessels stationary in warm water for extended periods and growth builds on tunnel walls, blades and gratings until manoeuvring performance is noticeably down at exactly the moment it is needed.
What it gets you
- Manoeuvring thrust restored ahead of a berthing or a pilotage that needs it
- Tunnel and grating flow cleared, not just the visible blade faces
- Seal, boss and anode condition documented while the divers are already down
- Reduced reliance on tug assistance where thrust had quietly degraded
Working conditions at Ennore
Ennore is a modern breakwater harbour just north of Chennai, so alongside work is sheltered and normally runs in parallel with cargo operations. The north-east monsoon from October to December sets the anchorage window; outside it the Bay of Bengal here is generally workable. Coal handling puts fine dust into the harbour water, so visibility around the bulk berths is materially lower than at the RoRo and liquid terminals a few hundred metres away — worth knowing before a survey scope is priced.
- Where we work
- Coal berths · RoRo berths · Liquid terminals · Anchorage
- Vessels we see here
- Bulk carriers · Pure car and truck carriers · LNG carriers · Product tankers
What we do at Ennore
- Full tunnel bore cleaned end to end, both openings, including the areas behind the gratings
- Blade and hub polished, with seal and boss condition inspected and reported
- Tunnel gratings cleared of growth and debris so flow is restored, not just the visible face
- Anodes inside the tunnel checked and wastage recorded
- Diving permission cleared with Kamarajar Port Limited, with the thruster confirmed isolated and tagged out before the dive
- Video record of tunnel and blade condition before and after
Planning the window at Ennore
The north-east monsoon governs the calendar at Ennore Port, roughly October to December. The Bay of Bengal also carries cyclone risk in April to June and again from October to December, so an anchorage attendance on this coast is planned with a standby allowance rather than a single fixed date. Because the harbour is sheltered, work here normally runs alongside or at a protected anchorage and can proceed in parallel with cargo operations rather than competing with them for the berth window.
Work is taken at the coal berths, RoRo berths, liquid terminals and anchorage, and which of those a vessel ends up at changes the dive plan more than the season does. Teams mobilise via Chennai (MAA), so give us the ETA as early as you have it — the travel is the flexible part, the approvals and the working window are not.
What we typically find at Ennore
Dry bulk handling here puts cargo dust into the water around the berths and anchorage. It settles on horizontal surfaces and packs into sea chest gratings and inlet openings, so inlet and grating clearance is routinely a larger part of the job at Ennore than owners budget for.
Shelter is a mixed blessing for a hull. The same calm that makes the port easy to work in is still water, and still water grows fouling faster than an exposed berth does.
Standard scope of work
Included as standard on every thruster cleaning attendance, wherever the vessel is. Anything outside it is quoted separately and flagged before mobilisation, never added afterwards.
- Tunnel cleaning
- Fouling removed from the full length of the tunnel bore, including the areas behind gratings where growth is heaviest.
- Blade cleaning and polishing
- Propeller blades and hub cleaned and polished to restore surface finish and reduce cavitation-inducing roughness.
- Grating and guard clearance
- Gratings and rope guards cleared of growth, netting and debris that restrict flow or risk fouling the unit.
- Condition inspection
- Blade edges, seals and visible gearcase condition inspected and recorded, with any damage reported immediately.
How we deliver it at Ennore
- 1
Scope and vessel details
Tell us the vessel, her particulars, the coating specification and the window at Ennore. We come back with a defined scope, a crew size and a duration we will stand behind. Where the conditions here will not support what has been asked for, we say so at this stage rather than after mobilisation.
- 2
Permits and approvals
Diving permission is obtained from Kamarajar Port Limited, along with terminal approval where the berth requires it and any environmental clearance for in-water work. This is handled by us, not left with the agent to chase.
- 3
Mobilisation to Ennore
Divers, compressors, brush carts and cameras mobilise via Chennai (MAA). Where a vessel is also calling at Chennai, one mobilisation is normally sized to cover both.
- 4
Safety setup and the dive
The vessel is secured for diving — main engine, shaft and thrusters immobilised, sea suctions confirmed shut, permit agreed with the master. Teams work under surface supervision with continuous diver communications and video throughout.
- 5
Report and handover
A completion report covering thruster cleaning is issued with before-and-after imagery, coating and anode condition and anything found that you should know about. The findings are discussed with the vessel rather than emailed and forgotten.
Ennore Port at a glance
- UN/LOCODE
- INENR
- Port type
- Major Port
- State
- Tamil Nadu
- Country
- India
- Water body
- Bay of Bengal
- Port authority
- Kamarajar Port Limited
- Main cargoes
- Thermal coal, Automobiles and RoRo, LNG, POL, General cargo
- Crew mobilisation
- Chennai (MAA)
- Services here
- Hull Cleaning, Hold Cleaning and Tank Cleaning
Frequently asked — Thruster Cleaning at Ennore
Do you provide thruster cleaning at Ennore Port?
Yes. Cleanship Marine works Ennore Port (INENR) in Tamil Nadu, India, covering the coal berths, RoRo berths, liquid terminals and anchorage. Teams mobilise via Chennai (MAA) with the full spread.
Can thruster cleaning be done while the vessel works cargo at Ennore?
Yes, in most cases. The harbour is sheltered enough that divers work alongside while cargo operations continue, and neither holds the other up. The vessel stays on hire throughout, and there is no diversion and no dry dock. We scope against the conditions at Ennore and tell you honestly whether the window you have is enough.
Do you need a diving permit from Kamarajar Port Limited?
Yes, and we obtain it. Diving permission from Kamarajar Port Limited, terminal approval where the berth requires it, and any environmental clearance for in-water work are arranged as part of the job rather than left with the agent. The master's permit to work and the immobilisation of machinery are agreed on board before anyone enters the water.
What is underwater visibility like at Ennore?
Visibility at Ennore Port is moderate, and it drops further around active bulk handling and after heavy rain, and the north-east monsoon sets the outer limits of the calendar. How the tide and sea state shape the dive plan is set out in full in the working-conditions section on this page.
Which vessels do you carry out thruster cleaning on at Ennore?
Bulk carriers, Pure car and truck carriers, LNG carriers, Product tankers — the traffic at Ennore Port runs to thermal coal, automobiles and roro, lng, so those are the profiles we see most. The scope is sized to the vessel, not to a standard package.
How quickly can a team mobilise to Ennore?
Divers and equipment mobilise via Chennai (MAA). Give us the ETA and the window and we will confirm what is achievable rather than promise a date we cannot hold. Where the vessel also calls at Chennai or Krishnapatnam, one mobilisation is often sized to cover both.
What does thruster cleaning at Ennore cost?
It depends on the vessel's dimensions and wetted area, the fouling state found, the coating specification and the working window available at Ennore. We would rather scope it properly and give you a specific figure than quote a headline rate that changes once the work starts. Send the details and the window at Ennore and you get a scoped price, usually the same working day.
Thruster Cleaning & Polishing at Ennore Port.
Tell us the vessel, her ETA at Ennore and the window. You get a scope, a crew size and an honest duration — usually the same working day.